Oil Rubbed Bronze
Black
Heavy Bronze
Pewter
Brushed Silver
FINISH
COATING THICKNESS
Optimize ventilation and aesthetics with the Air Window 0V 2H - Single Casement Portrait, a versatile choice for any room.
COATING THICKNESS
Type
Our dual pane tempered glass doors come with 1” T-Bar
Low E (Clear - completely see-through glass)
Frost/Sandblast
Flemish
Rain
Aquatex
Ribbed
Ford Blue
Watercube
Wood
Diamond
JAMB
Polyurethane Foam Core is filled in the jamb for greater insulation.
Threshold: Steel threshold is included and it comes welded on the jamb.
In Swing Threshold:
Out Swing Threshold:
Brackets: Tabs come welded on jamb with pre drilled holes to allow for easy installation.
Hinges: Steel weld on bullet hinges with grease fittings come welded on jamb and door. Allows customers to comfortably open our doors, but yet feel that quality with each and every use. We use welded steel bullet hinge with copper crush washer instead of a ball bearing hinge because ball bearings are made out of stainless steel (hard material) and the hinges/doors are made out of steel (softer material) which over time causes the hinge to wear. With copper crush washers, the washer is the soft point and they are easily replaceable over time if needed.
If you choose to purchase your hardware/lockset from a third party vendor, please make sure to provide them with the following specifications to ensure that your desired lockset will be compatible with our doors.
Bore hole size: | 2 1/8” |
Back set: | 2 3/4” |
Center to center: | 5 1/2” |
Door thickness: | 2” |
Bore Hole:
A bore hole is the doorknob hole that is drilled on the face of the door with a hole saw. The hole is drilled halfway through from each side. The hole saw is also used to drill the cross bore otherwise known as the latch hole. Both doorknob hole and latch holes come completed and drilled with every in stock order to help your installer install the lock at ease.
Center to Center:
The vertical distance measured between the center-points of the two bore holes. In other words, it is the measurement from the middle of the top bore hole to the middle of the bottom bore hole. This measurement is used to determine where a bore for the deadbolt is located above the bore for the latch. This information is important to help our customers purchase the correct compatible lock if you choose to purchase them from an outside hardware store. We have already done the homework for you by specifying the PINKYS locks that are compatible with your door if you choose to purchase the locks from PINKYS.
Back Set:
The backset is the distance from the edge of the door to the center of the 2-1/8” bore hole. The back set measurement is important to help our customers purchase the correct compatible lock with the correct latch size. We have already done the homework for you by specifying the PINKYS locks that are compatible with your door if you choose to purchase the locks from PINKYS. Our customers do not have to purchase the locks from PINKYS, you may purchase the locks from any local hardware store of your liking.
Door Thickness
REMOVABLE BUG SCREEN
SEE IT IN ACTION
IMPORTANT NOTE
the design of the door may alter or change to accommodate for the screen (most common example will be that of the designs with knuckles).
Our sizes are measured from outside of jamb to the outside of the jamb. For example, a 72” x 96” door listed on our website means that 72” is the width from outside to outside of jamb (not the actual width size of the door) and 96” is the height from outside of jamb to bottom of our built in steel threshold (not the actual height of the door).
We recommend the rough opening of the WIDTH to be 1/2” to 1” wider than the door size ordered to give the installer enough room to comfortably position the jamb into place and have enough room to make sure the jamb is leveled.
We recommend the rough opening of the HEIGHT to be 1/2” to 1” wider than the door size ordered to give the installer enough room to comfortably position the jamb into place and have enough room to make sure the jamb is leveled.
Our sizes are measured from outside of jamb to the outside of the jamb. For example, a 72” x 96” iron door listed on our website means that 72” is the width from outside to outside of jamb (not the actual width size of the door) and 96” is the height from outside of jamb to bottom of our built in threshold (not the actual height of the door)
We recommend the rough opening of the WIDTH to be 1/2” to 1” wider than the door size ordered to give the installer enough room to comfortably position the jamb into place and have enough room to make sure the jamb is leveled.
We recommend the rough opening of the HEIGHT to be 1/2” to 1” wider than the door size ordered to give the installer enough room to comfortably position the jamb into place and have enough room to make sure the jamb is leveled.
SWING OPTIONS
(RHI) Right hand in swing: You are facing the door standing outside, exterior side, of the door. The handle or lock will be on your left side, the hinges will be on the interior right side of the door and the door will swing towards the inside from left to right. When the door is at its open position, the door will be resting on the right interior side.
(LHI) Left hand in swing: You are facing the door standing outside, exterior side, of the door. The handle or lock will be on your right side, the hinges will be on the interior left side of the door and the door will swing towards the inside from right to left. When the door is at its open position, the door will be resting on the left interior side.
(RHO) Right hand out swing: You are facing the door standing outside, exterior side, of the door. The handle or lock will be on your left side, the hinges will be on the exterior right side of the door and the door will swing towards the outside from left to right. When the door is at its open position, the door will be resting on the right exterior side.
(LHO) Left hand out swing: You are facing the door standing outside, exterior side, of the door. The handle or lock will be on your right side, the hinges will be on the exterior left side of the door and the door will swing towards the outside from right to left. When the door is at its open position, the door will be resting on the left exterior side.
Swing Capacity: 180 degrees
This measurement shows the amount in degrees the hinge of the door allows for the door to fully open. Please note, every project site is different and this is solely dependent on nothing on site blocking the opening space of the door and the installation method your installer chooses to install the product. Please advise your installer before the installation day if you are in need of the door taking advantage of its full opening capability.
WHAT'S INCLUDED? DETAIL & SPEC
Door Thickness: 2”
Jamb
Jamb is included and packaged separately from the door. Jamb is constructed with 12 gauge tube (above industry standard). Polyurethane Foam Core is filled in the jamb for greater insulation.
Steel threshold is included and it comes welded on the jamb.
In Swing Threshold:
Out Swing Threshold:
Brackets
Tabs come welded on jamb with pre drilled holes to allow for easy installation.
Hinges
Steel weld on bullet hinges with grease fittings come welded on jamb and door. Allows customers to comfortably open our doors, but yet feel that quality with each and every use. We use welded steel bullet hinge with copper crush washer instead of a ball bearing hinge because ball bearings are made out of stainless steel (hard material) and the hinges/doors are made out of steel (softer material) which over time causes the hinge to wear. With copper crush washers, the washer is the soft point and they are easily replaceable over time if needed.
Glass
Tempered dual pane glass. There is a spacer in between each 1/4” thick glass that makes the total thickness of the tempered dual pane glass 5/8”. Front exterior side glass is the design glass style you chose and back interior side glass is clear. Customers may swap back glass for design glass with special orders only.
Weather Stripping
Dual foam weather stripping is included and comes installed around the door frame. Designs with operable glass will have dual sealing around the glass. The purpose is to help reduce air infiltration and water penetration. The dual sealing around the glass allows for weather stripping on both sides of the glass. The seal around the door frames help to reduce the leakage of air and heat, resulting in a much more energy efficient product for our customers.
Foam
Polyurethane foam core is filled in door frame and jamb to help reduce heat and cold weather transfer through the door. It also helps to reduce outside sound transfer through the door.
Rubber Door Sweeps
Door sweep located underneath the door is included and comes installed on door. Bottom sweeps are used to help seal the gap at the bottom of your door to help prevent infiltration of sound, light, drafts, insects, moisture, smoke or fire. The bottom sweep is a simple way to help in insulating a room, which provides cost and environmental benefits.
Flush Latch
Included and pre-installed on all double door orders (Unless otherwise specified). Our flush latch is installed on the upper and lower sections of the secondary door to allow both doors to open and operate while in the unlocked position.
Protection
Galvanize spray is used to help provide greater protection against corrosion for the iron base. Primer and paint is applied after the galvanizing process. During sustained periods of extreme cold weather, typically well below freezing of 25 degrees, is a good starting point to start looking further into our thermal break doors is to avoid condensation on the interior of the iron door.
Packaging
Carefully packaged, wrapped in foam, covered in cardboard, trunk wrapped and shipped with style from Los Angeles.
Customer Service
Our customer service does not stop at the point of sale. At PINKYS, customer satisfaction is our number one priority. We strive to provide our clients with superior service, quality and communication. Our team members will always be here to help answer any questions to ensure a smooth and rewarding experience.
Not included
Installation of door and locks. Locks are sold separately and can be purchased directly from our website.
Weight
Single Door Sizes | Approx. Weight (lbs) |
30" x 81" | 300 |
36" x 81" | 365 |
40" x 81" | 405 |
36" x 96" | 432 |
40" x 96" | 480 |
42" x 96" | 504 |
46" x 97.5" | 561 |
49" x 103" | 600 |
42" x 108" | 600 |
Round | Oval |
|
|
WHICH LOCK SET DO I NEED?
If you are ordering a single door - you only need (1) Active Lock.
If you are ordering a double door - you need (1) Active Lock & (1) Dummy Lock.
WHAT IS THE DIFFERENCE BETWEEN AN ACTIVE LOCK AND A DUMMY LOCK?
Single Doors
Double Doors
WHICH LOCK SET DO I NEED?
If you are ordering a single door - you only need (1) Active Lock.
If you are ordering a double door - you need (1) Active Lock & (1) Dummy Lock.
WHAT IS THE DIFFERENCE BETWEEN AN ACTIVE LOCK AND A DUMMY LOCK?
Single Doors
Double Doors