Color Sample - Oil Rubbed Bronze

Oil Rubbed Bronze

Color Sample - Black

Black

Color Sample - Heavy Bronze

Heavy Bronze

Color Sample - Pewter

Pewter

Color Sample - Silver Pewter

Brushed Silver

FINISH

  • We use automotive paint to coat our doors.
  • Galvanize spray is used to help provide greater protection against corrosion for the iron base.  Primer and automotive paint is applied after the galvanizing spray process.

COATING THICKNESS

  • Spray Primer Thickness - Around 180 microns
  • Paint Color Thickness - Around 30 microns
  • Clear Coat Thickness - Around 30 microns
  • Because all of our products are hand made and painted, color may differ a little from the photo. This ensures each order is one of a kind.

Type

Our dual pane tempered glass doors come with 1” T-Bar

Loe E glass

Low E (Clear - completely see-through glass)

  • Completely see-through glass design
  • It has mirror glass affect depending on sun angle

Glass Sample: Frost Sandblast Glass

Frost/Sandblast

Glass Sample: Flemish Glass

Flemish

Glass Sample: Rain Glass

Rain

Aquatex

Aquatex

Glass Sample: Ribbed Glass

Ribbed

Glass Sample: Ford Blue Glass

Ford Blue

Glass Sample: Watercube Glass

Watercube

Glass Sample: Wood Glass

Wood

Glass Sample: Diamond Glass

Diamond

JAMB

  • Jamb is included and packaged separately from the door. 
  • Jamb is constructed with 12 gauge tube (above industry standard).   

Polyurethane Foam Core is filled in the jamb for greater insulation. 

Threshold: Steel threshold is included and it comes welded on the jamb.

In Swing Threshold:

  • Thickness or height from the back interior side:  1 1/8”
  • Thickness or height from the front exterior side: 1/2”
  • Width or Depth:  6” 

 

Out Swing Threshold:

  • Thickness or height from the back interior side:  1 1/4”
  • Thickness or height from the front exterior side: 1/2”
  • Width or Depth:  6”

 

Brackets:  Tabs come welded on jamb with pre drilled holes to allow for easy installation.

Hinges: Steel weld on bullet hinges with grease fittings come welded on jamb and door.  Allows customers to comfortably open our doors, but yet feel that quality with each and every use.  We use welded steel bullet hinge with copper crush washer instead of a ball bearing hinge because ball bearings are made out of stainless steel (hard material) and the hinges/doors are made out of steel (softer material) which over time causes the hinge to wear. With copper crush washers, the washer is the soft point and they are easily replaceable over time if needed. 

 

Please note that Xanthis and other Iron Door locks are not compatible with AIR 4, AIR 5, OR AIR 7 doors.
BORE HOLE - LOCK SPEC

If you choose to purchase your hardware/lockset from a third party vendor, please make sure to provide them with the following specifications to ensure that your desired lockset will be compatible with our doors.

Bore hole size: 2 1/8”
Back set: 2 3/4”
Center to center: 5 1/2”
Door thickness: 2”
  • In stock single doors come with two pre drilled bore holes (one active lock needed) unless if otherwise specified.
  • In stock double doors come with two pre drilled bore holes on each door (one active lock and one dummy lock needed) unless if otherwise specified.
  • Locks purchased from PINKYS do not come installed on door upon delivery or shipment.  The reason for this is that it may get damage during the delivery or shipment process.  The installer will need to install the lock after the door installation is complete.

Bore Hole: 

A bore hole is the doorknob hole  that is drilled on the face of the door with a hole saw.  The hole is drilled halfway through from each side.  The hole saw is also used to drill the cross bore otherwise known as the latch hole.  Both doorknob hole and latch holes come completed and drilled with every in stock order to help your installer install the lock at ease.

Center to Center:

The vertical distance measured between the center-points of the two bore holes.  In other words, it is the measurement from the middle of the top bore hole to the middle of the bottom bore hole.  This measurement is used to determine where a bore for the deadbolt is located above the bore for the latch.  This information is important to help our customers purchase the correct compatible lock if you choose to purchase them from an outside hardware store.  We have already done the homework for you by specifying the PINKYS locks that are compatible with your door if you choose to purchase the locks from PINKYS.

Back Set:

The backset is the distance from the edge of the door to the center of the 2-1/8” bore hole.  The back set measurement is important to help our customers purchase the correct compatible lock with the correct latch size.  We have already done the homework for you by specifying the PINKYS locks that are compatible with your door if you choose to purchase the locks from PINKYS.  Our customers do not have to purchase the locks from PINKYS, you may purchase the locks from any local hardware store of your liking.

Door Thickness

REMOVABLE BUG SCREEN

SEE IT IN ACTION

IMPORTANT NOTE
the design of the door may alter or change to accommodate for the screen (most common example will be that of the designs with knuckles).

HOW OUR PRODUCTS ARE MEASURED

Our sizes are measured from outside of jamb to the outside of the jamb. For example, a 72” x 96” door listed on our website means that 72” is the width from outside to outside of jamb (not the actual width size of the door) and 96” is the height from outside of jamb to bottom of our built in steel threshold (not the actual height of the door).

We recommend the rough opening of the WIDTH to be 1/2” to 1” wider than the door size ordered to give the installer enough room to comfortably position the jamb into place and have enough room to make sure the jamb is leveled.

We recommend the rough opening of the HEIGHT to be 1/2” to 1” wider than the door size ordered to give the installer enough room to comfortably position the jamb into place and have enough room to make sure the jamb is leveled.

ROUGH OPENING

Our sizes are measured from outside of jamb to the outside of the jamb. For example, a 72” x 96” iron door listed on our website means that 72” is the width from outside to outside of jamb (not the actual width size of the door) and 96” is the height from outside of jamb to bottom of our built in threshold (not the actual height of the door)

We recommend the rough opening of the WIDTH to be 1/2” to 1” wider than the door size ordered to give the installer enough room to comfortably position the jamb into place and have enough room to make sure the jamb is leveled.

We recommend the rough opening of the HEIGHT to be 1/2” to 1” wider than the door size ordered to give the installer enough room to comfortably position the jamb into place and have enough room to make sure the jamb is leveled.

SWING OPTIONS

Right Hand Inswing LineArt

(RHI) Right hand in swing:  You are facing the door standing outside, exterior side, of the door.  The handle or lock will be on your left side, the hinges will be on the interior right side of the door and the door will swing towards the inside from left to right.  When the door is at its open position, the door will be resting on the right interior side.

Left Hand Inswing Line Art

(LHI) Left hand in swing:  You are facing the door standing outside, exterior side, of the door.  The handle or lock will be on your right side, the hinges will be on the interior left side of the door and the door will swing towards the inside from right to left.  When the door is at its open position, the door will be resting on the left interior side.

Left Hand Inswing Line Art
Right Hand Outswing Line Art

(RHO) Right hand out swing:  You are facing the door standing outside, exterior side, of the door.  The handle or lock will be on your left side, the hinges will be on the exterior right side of the door and the door will swing towards the outside from left to right.  When the door is at its open position, the door will be resting on the right exterior side.

Left Hand Outswing Line Art

(LHO) Left hand out swing:  You are facing the door standing outside, exterior side, of the door.  The handle or lock will be on your right side, the hinges will be on the exterior left side of the door and the door will swing towards the outside from right to left.  When the door is at its open position, the door will be resting on the left exterior side.

Left Hand Outswing Line Art

Swing Capacity Capability

Swing Capacity:  180 degrees

This measurement shows the amount in degrees the hinge of the door allows for the door to fully open. Please note, every project site is different and this is solely dependent on nothing on site blocking the opening space of the door and the installation method your installer chooses to install the product.  Please advise your installer before the installation day if you are in need of the door taking advantage of its full opening capability.

WHAT'S INCLUDED? DETAIL & SPEC

Door Thickness: 2” 

2" Door Thickness

Jamb

Jamb is included and packaged separately from the door.  Jamb is constructed with 12 gauge tube (above industry standard).   Polyurethane Foam Core is filled in the jamb for greater insulation.   

THRESHOLD

Steel threshold is included and it comes welded on the jamb.

In Swing Threshold:

  • Thickness or height from the back interior side:  1 1/8”
  • Thickness or height from the front exterior side: 1/2”
  • Width or Depth:  6” 

 

In Swing

 

Out Swing Threshold:

  • Thickness or height from the back interior side:  1 1/4”
  • Thickness or height from the front exterior side: 1/2”
  • Width or Depth:  6”

Outswing

 

Brackets

Tabs come welded on jamb with pre drilled holes to allow for easy installation.

 

Hinges

Steel weld on bullet hinges with grease fittings come welded on jamb and door.  Allows customers to comfortably open our doors, but yet feel that quality with each and every use.  We use welded steel bullet hinge with copper crush washer instead of a ball bearing hinge because ball bearings are made out of stainless steel (hard material) and the hinges/doors are made out of steel (softer material) which over time causes the hinge to wear. With copper crush washers, the washer is the soft point and they are easily replaceable over time if needed.     

 

Glass

Tempered dual pane glass.  There is a spacer in between each 1/4” thick glass that makes the total thickness of the tempered dual pane glass 5/8”.  Front exterior side glass is the design glass style you chose and back interior side glass is clear.  Customers may swap back glass for design glass with special orders only.

Glass Thickness

 

Weather Stripping

Dual foam weather stripping is included and comes installed around the door frame.  Designs with operable glass will have dual sealing around the glass.  The purpose is to help reduce air infiltration and water penetration.  The dual sealing around the glass allows for weather stripping on both sides of the glass.  The seal around the door frames help to reduce the leakage of air and heat, resulting in a much more energy efficient product for our customers.   

Window Stripping

 

Foam

Polyurethane foam core is filled in door frame and jamb to help reduce heat and cold weather transfer through the door.  It also helps to reduce outside sound transfer through the door. 

Foam

 

Rubber Door Sweeps

Door sweep located underneath the door is included and comes installed on door.  Bottom sweeps are used to help seal the gap at the bottom of your door to help prevent infiltration of sound, light, drafts, insects, moisture, smoke or fire.  The bottom sweep is a simple way to help in insulating a room, which provides cost and environmental benefits.

Rubber Door Sweeps

 

Flush Latch 

Included and pre-installed on all double door orders (Unless otherwise specified).  Our flush latch is installed on the upper and lower sections of the secondary door to allow both doors to open and operate while in the unlocked position.

Flush Latch

 

Protection

Galvanize spray is used to help provide greater protection against corrosion for the iron base.  Primer and paint is applied after the galvanizing process.  During sustained periods of extreme cold weather, typically well below freezing of 25 degrees, is a good starting point to start looking further into our thermal break doors is to avoid condensation on the interior of the iron door.

 

Packaging

Carefully packaged, wrapped in foam, covered in cardboard, trunk wrapped and shipped with style from Los Angeles. 

 

Customer Service

Our customer service does not stop at the point of sale. At PINKYS, customer satisfaction is our number one priority.  We strive to provide our clients with superior service, quality and communication.  Our team members will always be here to help answer any questions to ensure a smooth and rewarding experience.

 

Not included 

Installation of door and locks. Locks are sold separately and can be purchased directly from our website.

 

Weight

 Single Door Sizes Approx. Weight (lbs)
30" x 81" 300
36" x 81" 365
40" x 81" 405
36" x 96" 432
40" x 96" 480
42" x 96" 504
46" x 97.5" 561
49" x 103" 600
42" x 108" 600

Interior Knob Shape

 Round Oval

Round

Round

WHICH LOCK SET DO I NEED?

If you are ordering a single door - you only need (1) Active Lock.

If you are ordering a double door - you need (1) Active Lock & (1) Dummy Lock. 

Active & Dummy Locks

WHAT IS THE DIFFERENCE BETWEEN AN ACTIVE LOCK AND A DUMMY LOCK?

Single Doors

  • Require an Active lock only. 

Double Doors

  • Require an Active lock, which is your locking hardware, to be installed on your active door or the door that is used most often. 
  • Require a Dummy lock,  which has no mechanical latch mechanism, to be installed on the secondary door.
  • Dummy locks do not function - the main purpose of a dummy lock is for aesthetic purposes only.

    WHICH LOCK SET DO I NEED?

    If you are ordering a single door - you only need (1) Active Lock.

    If you are ordering a double door - you need (1) Active Lock & (1) Dummy Lock. 

    Active & Dummy Locks

    WHAT IS THE DIFFERENCE BETWEEN AN ACTIVE LOCK AND A DUMMY LOCK?

    Single Doors

    • Require an Active lock only. 

    Double Doors

    • Require an Active lock, which is your locking hardware, to be installed on your active door or the door that is used most often. 
    • Require a Dummy lock,  which has no mechanical latch mechanism, to be installed on the secondary door.
    • Dummy locks do not function - the main purpose of a dummy lock is for aesthetic purposes only.